Administration

  • UCX Software - SIP Trunks
SIP Trunking between Panasonic NSX00 and UCX

This page describes how to set up a SIP trunk between a Panasonic NS1000 or NS700 and the UCX.

NOTE

E-MetroTel's UCX uses a default signaling port UDP 5060 for both sending and listening. Panasonic systems use a default SIP sending UDP port of UDP 5060, but a default listening port of UDP 35060, causing a mismatch between the default settings.

The port can be modified on either the Panasonic or UCX system.

Scenario 1: Modify the Panasonic to use port 5060

Note: The Panasonic uses port 5060 for SIP extensions. This configuration scenario can be used if the Panasonic system does not have existing SIP extensions configured.

Configure SIP Trunk on the UCX

  1. Open UCX Administration and navigate to the PBX / IP Trunk Assistant tab
  2. Click on New Account
  3. Input an Account Name (eg. To_Panasonic)
  4. Ensure that the Trunk Provider is set to UCX (the default setting)
  5. In the Host / IP field, input the details of the Panasonic system (eg. 192.168.1.222)
  6. The remaining fields can all remain at the defaults for the UCX Trunk Provider settingSIPTrunkToPanasonic.png

Configure SIP Trunk on the Panasonic NSx000

  1. Change UDP port for SIP Extension Server from 5060 to some other in my example to 15060. It is at Setup/PBX Configuration/1. Slot/Port NumberNS1000ModifySIPExtensionPort.png
  2. Change Sip Client Port Number (used for Trunks) from 35060 to 5060. It is at Setup/PBX Configuration/1. Slot/V-SIPGW and Shelf PropertyNS1000ShelfProperty.png

    NS1000SIPClientPortNum.png

  3. Configure the required number of SIP channels to UCX at the Virtual SIP Gateway in the Port PropertyNS1000PortProperty.png

    NS1000PortPropertyA.png

    NS1000PortPropertyB.png
    (It does not matter what values are input for Name and Authentication ID)

    NS1000PortPropertyC.png

    (Note: the UCX is at 192.168.1.20)

    NS1000PortPropertyD.png

  4. Put the virtual card to InsNS1000VirtualTrunkINS.png

Scenario 2: Modify the UCX to send using port 35060

In this scenario, the UCX sends invites to Panasonic on port 35060 and receives invites on port 5060, while the Panasonic sends invites to UCX on port 5060 and receives invites at port 35060.

Configure SIP Trunk on the UCX

  1. Open UCX Administration and navigate to the PBX / IP Trunk Assistant tab
  2. Click on New Account
  3. Input an Account Name (eg. To_Panasonic)
  4. Ensure that the Trunk Provider is set to UCX (the default setting)
  5. In the Host / IP field, input the details of the Panasonic system with the desired port number appended (eg. 192.168.1.222:35060)
  6. The remaining fields can all remain at the defaults for the UCX Trunk Provider settingNS1000UCX35060port.png

Configure SIP Trunk on the Panasonic NSx000

  1. Configure 2 SIP channels to UCX on the Virtual SIP Gateway in the Port Property. It is the same setting as at first scenario without changing ports.NS1000PortProperty.png

    NS1000PortPropertyA.png

    NS1000PortPropertyB.png
    (It does not matter what values are input for Name and Authentication ID)

    NS1000PortPropertyC.png
    (Note: the UCX is at 192.168.1.20)

    NS1000PortPropertyD.png

  2. Put the virtual card to InsNS1000VirtualTrunkINS.png

UCX Routes

Once the SIP trunks have been configured, you can add Inbound and Outbound routes on both systems to direct traffic between them.

UCX Outbound Routes

The following is an example of how to set up the Outbound Routes on the UCX.

NS1000UCXOutboundRoute.png

UCX Inbound Routes

The following is an example of how to set up the Inbound Routes on the UCX.

NS1000UCXInboundRoute.png

Panasonic Routes

Panasonic Incoming Calls

The following is an example of how to set up the Panasonic for incoming calls.

NS1000DIDTable.png

NS1000COLineTable.png

Panasonic Outgoing Calls

The following is an example of how to set up the Panasonic for outgoing calls.

NS1000TRGSettings.png

NS1000DialingPlan.png

NS1000ExtensionSettings.png

How to make a call

To call from a UCX phone to an extension on the Panasonic, just dial 301 or 302 and the call will be started.

To call from a Panasonic extension to a phone on the UCX you must dial *37009101 (or …102)  or *37010101 (or …102).

Contents